OPTIMALISASI DESAIN JIG VALVE SPRING COMPRESSOR DENGAN DOUBLE FLANGE UNTUK EFISIENSI PELEPASAN DAN PEMASANGAN KATUP MESIN

Renita Dewi, Shafa Amatullah Fatin, Krisna Chandra Wijaya, Anisa Ramadhani, Ghany Heryana

Abstract


This research aims to develop a new design of Jig Valve Spring Compressor that uses double flange, replacing the previous design that only uses one flange. This new design, which is still under development, has the potential to increase the speed and efficiency of the cylinder head overhaul process which has previously shown an increase in time efficiency of up to 82%. The development of this design is based on ergonomic principles using the OWAS  method to minimize the risk of musculoskeletal injuries and improve the working comfort of technicians during the engine valve removal and installation process.


Full Text:

PDF

References


Abadi, A.H. et al. (2021) ‘DESIGN OF SPECIAL SERVICE TOOLS ( SST ) MOTORCYCLE TIMING GEAR’, 8(2), pp. 22–30.

Abadi, A.H. et al. (2021) ‘DESIGN OF SPECIAL SERVICE TOOLS ( SST ) MOTORCYCLE TIMING GEAR’, 8(2), pp. 22–30.

Andrian, D. and Renilaili, R. (2021) ‘Pengukuran Tingkat Risiko Ergonomi Dengan Menggunakan Metode Ovako Working Analysis System (OWAS) Untuk Mengurangi Risiko Muscoleskeletal’, Integrasi : Jurnal Ilmiah Teknik Industri, 6(1), p. 32. Available at: https://doi.org/10.32502/js.v6i1.3793.

Bastuti, S., Zulziar, M. and Suaedih, E. (2019) ‘Analisis Postur Kerja Dengan Metode Owas (Ovako Working Posture Analysis System) Dan Qec (Quick Exposure Checklist) Untuk Mengurangi Terjadinya Kelelahan Musculoskeletal Disorders Di Pt. Truva Pasifik’, Jitmi, 2(2), pp. 2685–6123.

Budiman, E. and Setyaningrum, R. (2012) ‘Perbandingan Metode-Metode Biomekanika Untuk Menganalisis Postur Pada Aktivitas Manual Material Handling (Mmh) Kajian Pustaka’, Jgti Undip: Jurnal Teknik Industri, 1(3), pp. 46–52.

Della, T.L., Farras, M.F. and Hamid, A.N. (2019) ‘Evaluasi Desain Sistem Kerja Terhadap Output REBA Pengangkatan Air Minum Kemasan berdasarkan Prinsip Manual Material Handling’, Idec.Ft.Uns.Ac.Id, (Capodaglio 2017), pp. 2–3. Available at: https://idec.ft.uns.ac.id/wp-content/uploads/2019/05/ID132.pdf.

Irwan, E. et al. (2021) ‘Rancang Bangun Mesin Pemotong Kentang Berbentuk Stick’, 7(1), pp. 25–29.

Nasution, S. and Razali (2019) ‘Analisa Kegagalan Cylinder Head Mesin Diesel Komatsu Dengan Menggunakan Metode Failure Mode and Effect Analysis (FMEA) di Megapower PLTD Bengkalis’, Seminar Nasional Industri dan Teknologi (SNIT), (2012), pp. 236–262. Available at: http://eprosiding.snit-polbeng.org/index.php/snit/article/view/88.

Prassetiyo, H., Rispianda, R. and Adanda, H. (2016) ‘Rancangan Jig Dan Fixture Pembuatan Produk Cover on-Off’, Teknoin, 22(5), pp. 350–360. Available at: https://doi.org/10.20885/teknoin.vol22.iss5.art4.

Rahayu, W.E. and Romalasari, A. (2020) ‘PENGGUNAAN MEDIA TANAM DAN PUPUK NPK TERHADAP HASIL RUMPUT TEKI (Cyperus rotundus) SERTA ANALISA KANDUNGAN KERIPIK OLAHANNYA’, Jurnal Ilmiah Ilmu dan Teknologi Rekayasa, 2(1), pp. 21–25. Available at: https://doi.org/10.31962/jiitr.v2i1.27.

Ramadhan, M.R., Achiraeniwati, E. and Sri Rejeki, Y. (2023) ‘Pengukuran Level Resiko pada Stasiun Kerja Pengukuran Menggunakan Kuesioner Nordic Body Map (NBM), dan Ovako Working Posture Analysis System (OWAS) (Studi Kasus: CV X)Pen’, Bandung Conference Series: Industrial Engineering Science, 3(1), pp. 426–433. Available at: https://doi.org/10.29313/bcsies.v3i1.7037.

Renita Dewi (2023) RANCANG BANGUN JIG VALVE SPRING COMPRESSOR UNTUKMEMPERCEPAT PROSES PELEPASAN DAN PEMASANGAN KATUP PADA CYLINDER HEAD ENGINE TOYOTA 4A-FE, Politeknik Negeri Jakarta. Politeknik Negeri Jakarta.

Subekhi, T.U.A. et al. (2023) ‘Rancang Bangun Mesin Pencacah Nangka Muda Sebagai Bahan Produksi Makanan Megono’, Journal of Applied Mechanical Technology, 2(1), pp. 1–9. Available at: https://doi.org/10.31884/jamet.v2i1.27.

Sumarta, D.M. (2022) ‘Perancangan Mesin Pengupas Ceri Kopi Dengan Penggerak Mula Motor Listrik Menggunakan Metode French’, Sistemik : Jurnal Ilmiah Nasional Bidang Ilmu Teknik, 10(2), pp. 66–71. Available at: https://doi.org/10.53580/sistemik.v10i2.71.




DOI: https://doi.org/10.31884/jtt.v11i2.703

Refbacks

  • There are currently no refbacks.


Copyright (c) 2025 JTT (Jurnal Teknologi Terapan)



View Stats

 

 Creative Common Attribution-ShareAlike 4.0 International (CC BY-SA 4.0)